boot.h
2.21 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
#ifndef __BBBOOT_HDR__
#define __BBBOOT_HDR__
/* defines here are for IDE3 simulator commands */
#include <PR/bbsim.h>
/* virage2 checksum value */
#define VIRAGE2_CHECKSUM 0x00bbc0de
/* load the number of pages it takes to fill the bram */
// #define LOAD_SK_PAGES \
// ((BOOT_RAM_HI_END-BOOT_RAM_HI_START)>>PI_FLASH_PAGE_ADDR_SHIFT)
#define LOAD_SK_PAGES 2
/* return and error code definitions */
#define FLASH_SUCCESS 0
#define ERROR_FLASH_CTRL_DOUBLE_BIT -1
#define ERROR_FLASH_MODULE_REMOVED -2
/* For "fatal" errors (double-bit ecc, bad hash, bad v2 checksum) */
#if defined(_LANGUAGE_C)
#define JUMP_HANDLER \
TRACE(0xbaad); \
asm(".set noreorder; li $8, 0xbfc00200; jr $8; nop; .set reorder")
#elif defined(_LANGUAGE_ASSEMBLY)
#define JUMP_HANDLER \
TRACE_VAL(0xbaad); \
li t0, 0xbfc00200; \
jr t0; \
nop
#endif /* _LANGUAGE_ */
/* HALT_SIM will shutdown the simulator by writing to
* IDE3. Since we're using IDE3 to output trace info
* it is OK to retain this code when not using the
* simulator (real chip). The writes will still go out
* but they will have no impact.
*/
#if defined(_LANGUAGE_C)
#define HALT_SIM /* power down */ \
IDE_WRITE(PI_IDE3_SIM_HALT,0); \
while(1){}
#elif defined(_LANGUAGE_ASSEMBLY)
#define HALT_SIM \
li t0, PHYS_TO_K1(PI_IDE_CONFIG_REG); \
lw t1, 0(t0); \
and t1, ~PI_IDE_CONFIG_RESET; \
sw t1, 0(t0); \
sh zero, PHYS_TO_K1(PI_IDE3_SIM_HALT); \
lw t0, PHYS_TO_K1(PI_IDE_FC_BASE_REG)
#endif /* _LANGUAGE_ */
/* trace macros */
#define TRACE_OUTPUT_REG PI_IDE3_BASE_REG
#if defined(_LANGUAGE_C)
#define TRACE(val) (IDE_WRITE(TRACE_OUTPUT_REG,(val)))
#endif
#if defined(_LANGUAGE_ASSEMBLY)
#define TRACE_ADDR PHYS_TO_K1(TRACE_OUTPUT_REG)
#define TRACE_VAL_REG t7
#define TRACE_VAL(val) \
li TRACE_VAL_REG,(val); \
sh TRACE_VAL_REG, TRACE_ADDR; \
lw TRACE_VAL_REG, PHYS_TO_K1(PI_IDE_FC_BASE_REG)
#define TRACE_REG(_r) \
sh _r, TRACE_ADDR; \
srl TRACE_VAL_REG, _r, 0x10 ; \
sh TRACE_VAL_REG, TRACE_ADDR; \
lw TRACE_VAL_REG, PHYS_TO_K1(PI_IDE_FC_BASE_REG)
#endif
#endif